Parking system common fault q&a
2023-10-07 00:00:00
problem a: tao brake falls in a bar or rod, movement only a short distance before they will stop to be not moved, this is how to return a responsibility?
a: this is due to the way the brake motor initial in position signal from the sensor without induction to the controller, the solution is simple, continue to press the fall on the remote control lever, according to a few times more until the brake lever fall in place, and then press rising stem, the brake lever up reach the designated position, debugging repeatedly several times the rod rod, problem can be solved.
problem two: the brake in stem, no fall in place and stop to be not moved, this is what causes?
a: a problem is caused by not signal, the problem is the motor displacement caused by the stroke switch.At this moment need to open the gate motherboard shield, in the middle of the main board to the location of the right trip switch, a motor must dial 6 seconds of motor to the position of 6 s (6 seconds), 3 seconds to 3 s, 1 second for 1 s, is to better match the configuration.
question three: brake is a lever up reach the designated position, stay for a few seconds after the brake lever will automatically fall, this how to solve?
a: at this time due to the brake lever switch does not reach the designated position caused by falling, solving steps are as follows:
1.First rule out the factors of feeling, and pull the detector.
2. Open the main cover, in the middle of the motherboard right there are three groups to dial the code switch lock without this configuration (before 2011), 1, 2 of them are regulating rod falling delay, 1, 2, all OFF without delay, 3 is ON automatic release, at this time to fall won’t fall rod rod signal.
if you still can’t solve the problem, after all these reasons are ruled out should be motherboard chip failure cause, please tell the mainboard to return our corresponding dealer for further processing.
question 4: use the remote control, brake, the brake motor have no reaction, but the light on the motherboard is normal, how to deal with this?
a: may be has the following two reasons: 1. Motor card dead;2. Start the capacitance.
the solution is as follows:
to open the lock cover, check whether the damping rubber mat is damaged.If damage will cause the motor jammed, directly below the central position of the rotating motor shaft can outsource or tool (necessary) from active crank arm stuck position.Step 1 after treatment still cannot solve the problem, can replace start switch capacitance, solve the problem.
problem five: remote control can’t control the brake, but drive-by-wire control is normal, what reason is this?
a: this may be due to the mainboard remote control receiving circuit problems solving steps are as follows:
make sure the remote control board accept signal is normal.Indicator light is normal, the replacement motherboard for the remote control receiver plug area 9013 transistors (general electronic market to buy).If can’t solve the problem, the motherboard return the corresponding dealers into the next phase of processing.
question 6: how to use the right way brake clutch?
a: the method is as follows:
1, when a power outage, or need to normally open the gate, can make the gate after rising stem in place, with the word of the clutch handle will brake clutch rotation to the [from] position, also suggested that broken brake power.
2, when close the clutch, available remote control way brake motor turning active crank arm and the connecting rod overlap or into a straight line, with the hand brake lever pulled down at this time, at the same time turn the clutch to the position of the [us].
question 7: the brake lever in the fall, fall does not reach the designated position automatically bounce, what reason be?
a: this is caused by the unbalance of spring tension, the solution is as follows: when the spring tension is balance, from the tao brake clutch, the rod at 40 degrees & ndash;60 degrees can stable at any location at this time is the best state.If the unbalanced spring, spring tension is bigger, then there will be a pole does not reach the designated position automatically rebound phenomenon.At this point can be left rotation spring adjusting knob (spring cover below), until spring tension balance.
experiences: the north the weather is cold in winter, can be appropriately adjust the spring tension, keep the brake normal use.
question 8: USB card machine can’t read the card, what reason is this?
a: this is because the USB card after long time need not, automatically start the computer USB power saving mode.The solution is simple, the credit card USB plug in to reconnect.Here we recommend you if long time don’t use credit card, please pull out the USB interface, because there are some computers will to power saving often unused equipment protection.